An Electric Scooter Community on a Mission to Stamp out Transportation Mediocrity.

Covers electric scooter models whether shared or for consumers.
By Tony Lac
Posts
#5983
We should all post what we did to successfully get one of these running here. I was thinking of using m365 dasboard and controller. Since this scoot is so much more bigger maybe 2wd? Thoughts?
Pez, Mikolajit liked this

By Colburn
Posts
#5985
No, the M365 and Bird Zero aren’t even remotely similar in terms of using the same circuit. Check the technology forum section for more information.

If you’re considering using the bird zero wheel on a M365 , it is possible.

You’ll need to know how to solder and have patience if you’re willing to do the conversion.
Gahnen liked this

By 07Gevish
Posts LikeBB
#6041
To view images REGISTER or LOGIN for full access.

Successfully converted to run.
However lights and dash not working...so it's difficult to tell the battery charge.
Used one of the generic 36v 350W controllers and simple ignition/grip throttle.
Nets187, RyanH43165 liked this

By Colburn
Posts
#6051
07Gevish wrote:
Tue Mar 12, 2019 3:40 am
To view images REGISTER or LOGIN for full access.

Successfully converted to run.
However lights and dash not working...so it's difficult to tell the battery charge.
Used one of the generic 36v 350W controllers and simple ignition/grip throttle.
Really nice , do you have the link for those ? The ones in the technology board are dead.

As for the soldering part, you just removed the controller I assume? I’m trying to figure out where you tucked it in.

By 07Gevish
Posts LikeBB
#6052
Colburn wrote:
Tue Mar 12, 2019 12:39 pm
07Gevish wrote:
Tue Mar 12, 2019 3:40 am
To view images REGISTER or LOGIN for full access.

Successfully converted to run.
However lights and dash not working...so it's difficult to tell the battery charge.
Used one of the generic 36v 350W controllers and simple ignition/grip throttle.
Really nice , do you have the link for those ? The ones in the technology board are dead.

As for the soldering part, you just removed the controller I assume? I’m trying to figure out where you tucked it in.
https://www.amazon.com/Electric-Control ... pons&psc=1
https://www.amazon.com/gp/aw/d/B07D72MD ... UTF8&psc=1

And yes I have removed the old controller and put the replacement where the old one was. It fit with so e extra room too.
Ni Go, Luscious1, Chazz liked this

User avatar
By Pez
Posts LikeBB Avatar
#6055
Man I love what you have done with the ZERO .. This is a must have item for sure . To bad everyone out in the streets are beat to hell and have bald tires front and back ..total hunks of Shit

By Colburn
Posts
#6067
Pez wrote:
Tue Mar 12, 2019 5:47 pm
Man I love what you have done with the ZERO .. This is a must have item for sure . To bad everyone out in the streets are beat to hell and have bald tires front and back ..total hunks of Shit
Where do you live ? There’s a ton in Santa Monica.
Nets187 liked this

By Colburn
Posts
#6068
07Gevish wrote:
Tue Mar 12, 2019 2:13 pm
Colburn wrote:
Tue Mar 12, 2019 12:39 pm
07Gevish wrote:
Tue Mar 12, 2019 3:40 am
To view images REGISTER or LOGIN for full access.

Successfully converted to run.
However lights and dash not working...so it's difficult to tell the battery charge.
Used one of the generic 36v 350W controllers and simple ignition/grip throttle.
Really nice , do you have the link for those ? The ones in the technology board are dead.

As for the soldering part, you just removed the controller I assume? I’m trying to figure out where you tucked it in.
https://www.amazon.com/Electric-Control ... pons&psc=1
https://www.amazon.com/gp/aw/d/B07D72MD ... UTF8&psc=1

And yes I have removed the old controller and put the replacement where the old one was. It fit with so e extra room too.
Amazing , thanks man ! Any soldering required ?

By 07Gevish
Posts LikeBB
#6114
Colburn wrote:
07Gevish wrote:
Tue Mar 12, 2019 2:13 pm
Colburn wrote:
Tue Mar 12, 2019 12:39 pm
Really nice , do you have the link for those ? The ones in the technology board are dead.

As for the soldering part, you just removed the controller I assume? I’m trying to figure out where you tucked it in.
https://www.amazon.com/Electric-Control ... pons&psc=1
https://www.amazon.com/gp/aw/d/B07D72MD ... UTF8&psc=1

And yes I have removed the old controller and put the replacement where the old one was. It fit with so e extra room too.
Amazing , thanks man ! Any soldering required ?
It's not quite plug and play. I took off the connectors from original control board and soldered them on to the new one. Also soldered the throttle connectors to the new controller. Warning. After you finished connecting controller to the motor and throttle but before you connect the battery make sure 2 dark green wires on the new controller arent connected to each other or it will cause the motor to engage as soon as you plug the battery in.

User avatar
By Pez
Posts LikeBB Avatar
#6118
Would love to know if your trying to figure out the lights and dashboard ..to get them up and running . The Zero is very special ..#personalzero amazing . I’ve had Zeros do 26mph stock when I was a mechanic ..

  • 1
  • 2
  • 3
  • 4
  • 5
  • 50
Ninebot Max firmware

Link to all OEM Max firmware: https://files.scoote[…]

NineBot Max - Attempt

So to clarify - All we need to do is flash the[…]

I used the gps board to convert the power to 5v fo[…]

I buy in internet a electric scooter from lime co[…]