An Electric Scooter Community on a Mission to Stamp out Transportation Mediocrity.

Covers electric scooter models whether shared or for consumers.
#52556
Javi30 wrote:
Mon Oct 05, 2020 4:25 am
Mick Ray wrote:
Fri Oct 02, 2020 11:22 am
To sum up:
- 06E should disappear when you send any command to controller (on, light off, light on, etc.) - the best way is to program device that sends some command interval 2-7 minutes.
- 06E should disappear after restarting scooter (this is option with green box)

And...
If you know command to enable scooter in newer version, please give some info. Thank you
That’s the thing.. my 06e isn’t going away when I send a code (light on code works on my new firmware scooter but the one with the old firmware isn’t receiving the codes anymore)

Imgur link to pictures, and I’ll try to post them in line here as well: https://imgur.com/gallery/06ES1z4

Old firmware realterm:
To view images REGISTER or LOGIN for full access.


New firmware realterm:
To view images REGISTER or LOGIN for full access.
Hello Is it possible to save through st-link v2 a save old firmware scooter and put on a new scooter on which the engine does not work and try to start the engine? Does the scooter work with STM32 controller?
I have Lime sj 2.5
SANTR_FW_2.4.26_20191119100000




#52796
moiskey wrote:
Fri Mar 19, 2021 7:18 pm
greetings, you have the code to test with an arduino nano and its diagram. I have an old one to try To view images REGISTER or LOGIN for full access.
Hello!
Please, can you send this code and diagram to me too? I have a scooter too, and I can't use it To view images REGISTER or LOGIN for full access.

#52820
x1p1lag wrote:
Sun Mar 21, 2021 1:27 am
moiskey wrote:
Fri Mar 19, 2021 7:18 pm
greetings, you have the code to test with an arduino nano and its diagram. I have an old one to try To view images REGISTER or LOGIN for full access.
Hello!
Please, can you send this code and diagram to me too? I have a scooter too, and I can't use it To view images REGISTER or LOGIN for full access.
Code: Select all
byte ON[9] = {0x46, 0x43, 0x16, 0x61, 0x00, 0x01, 0xF1, 0xF2,  0x8F};
void setup() {Serial.begin(9600);}
void loop()  {Serial.write(ON, sizeof(ON));delay(500);}
Note that it will only work on NON PATCHED gen 2.5 scooters.

#52827
Risitas98 wrote:
Mon Mar 22, 2021 12:27 pm
x1p1lag wrote:
Sun Mar 21, 2021 1:27 am
moiskey wrote:
Fri Mar 19, 2021 7:18 pm
greetings, you have the code to test with an arduino nano and its diagram. I have an old one to try To view images REGISTER or LOGIN for full access.
Hello!
Please, can you send this code and diagram to me too? I have a scooter too, and I can't use it To view images REGISTER or LOGIN for full access.
Code: Select all
byte ON[9] = {0x46, 0x43, 0x16, 0x61, 0x00, 0x01, 0xF1, 0xF2,  0x8F};
void setup() {Serial.begin(9600);}
void loop()  {Serial.write(ON, sizeof(ON));delay(500);}
Note that it will only work on NON PATCHED gen 2.5 scooters.
Thanks and Yeah I needed it to test out if it had been patched or not since it's been sitting around since late 2019


  • 1
  • 14
  • 15
  • 16
  • 17
  • 18
Bird 2

So did anybody successfully charged the battery?

Got any update on this? If you can read this d[…]

Do i need to do anthing else to the scooter apart […]

The way the ES-400 communicates is fundamentally[…]