An Electric Scooter Community on a Mission to Stamp out Transportation Mediocrity.

Covers electric scooter models whether shared or for consumers.
#52556
Javi30 wrote:
Mon Oct 05, 2020 4:25 am
Mick Ray wrote:
Fri Oct 02, 2020 11:22 am
To sum up:
- 06E should disappear when you send any command to controller (on, light off, light on, etc.) - the best way is to program device that sends some command interval 2-7 minutes.
- 06E should disappear after restarting scooter (this is option with green box)

And...
If you know command to enable scooter in newer version, please give some info. Thank you
That’s the thing.. my 06e isn’t going away when I send a code (light on code works on my new firmware scooter but the one with the old firmware isn’t receiving the codes anymore)

Imgur link to pictures, and I’ll try to post them in line here as well: https://imgur.com/gallery/06ES1z4

Old firmware realterm:
Image

New firmware realterm:
Image
Hello Is it possible to save through st-link v2 a save old firmware scooter and put on a new scooter on which the engine does not work and try to start the engine? Does the scooter work with STM32 controller?
I have Lime sj 2.5
SANTR_FW_2.4.26_20191119100000
#52820
x1p1lag wrote:
Sun Mar 21, 2021 1:27 am
moiskey wrote:
Fri Mar 19, 2021 7:18 pm
greetings, you have the code to test with an arduino nano and its diagram. I have an old one to try :D
Hello!
Please, can you send this code and diagram to me too? I have a scooter too, and I can't use it :(
Code: Select all
byte ON[9] = {0x46, 0x43, 0x16, 0x61, 0x00, 0x01, 0xF1, 0xF2,  0x8F};
void setup() {Serial.begin(9600);}
void loop()  {Serial.write(ON, sizeof(ON));delay(500);}
Note that it will only work on NON PATCHED gen 2.5 scooters.
#52827
Risitas98 wrote:
Mon Mar 22, 2021 12:27 pm
x1p1lag wrote:
Sun Mar 21, 2021 1:27 am
moiskey wrote:
Fri Mar 19, 2021 7:18 pm
greetings, you have the code to test with an arduino nano and its diagram. I have an old one to try :D
Hello!
Please, can you send this code and diagram to me too? I have a scooter too, and I can't use it :(
Code: Select all
byte ON[9] = {0x46, 0x43, 0x16, 0x61, 0x00, 0x01, 0xF1, 0xF2,  0x8F};
void setup() {Serial.begin(9600);}
void loop()  {Serial.write(ON, sizeof(ON));delay(500);}
Note that it will only work on NON PATCHED gen 2.5 scooters.
Thanks and Yeah I needed it to test out if it had been patched or not since it's been sitting around since late 2019
#54487
Marley29 wrote:
Mon Oct 28, 2019 5:28 pm
Well thank you for your response I'm new to micro chargers and the bluetooth setup well all of this is new to me i have figured out a method to get them on light work dash works but if you could pm me or email me i would greatly appreciate it kinda need a walk through from here your simplest way to get the heart back beating I've been reading the forum for months and i finally come across your thread
Image
Image
Could you please provide a solution?
  • 1
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21

Any one got any info on beryl bikes I seen a few i[…]

Hej Guys got my hands on this double battery pac[…]

As this was a rental version whos overstock was ev[…]

This last transistor needs to be soldered. https:[…]